A garbage disposal that's been making grinding sounds for months before stopping entirely often has a seized bearing or cracked impeller โ signs the motor isn't worth repairing. Our techs in Upper Falls tell you honestly whether a repair or a same-day unit swap makes more financial sense.
๐ Call +1-855-718-1500 โ Same-Day Service
We carry replacement units on the truck in common horsepower ratings so a same-day swap is possible when the motor has genuinely failed.
A disposal that hums but won't spin almost always just needs the jam cleared with an Allen wrench at the center socket and the reset button pressed โ a 5-minute fix that doesn't require a new unit.
InSinkErator (Badger, Badger 5, Compact, Evolution series), Moen GXS/GX series, Waste King, KitchenAid, and Whirlpool disposals all mount differently and have specific jam-clearing procedures. We know the mounting assembly for each brand and carry the correct jam-clearing wrench sizes.
A disposal that jams once is worth clearing and resetting. A disposal that jams repeatedly, has a seized turntable bearing, emits burning smells, or is over 10 years old is likely approaching motor failure โ and the repair cost of a failed motor exceeds the cost of a new unit.
A disposal installed without properly removing the dishwasher drain knockout plug is a common installation error that floods the dishwasher interior. We check this and correct it if present.
Most disposal calls complete in 30โ60 minutes โ same visit, flat-rate pricing.
If the jam-clearing wrench won't budge the impeller, the motor shaft may be seized rather than just stuck from debris โ we distinguish between the two before recommending replacement.
A disposal that makes no sound when switched on has either tripped its thermal overload protector (the red button on the bottom โ press it and try again) or has a wiring issue at the switch or disposal unit. We check the reset button, test for power at the disposal's wire connection, and test the wall switch for continuity.
We identify the leak source before recommending any repair. A sink collar re-seal is a 30-minute job. A unit with a cracked body has no cost-effective repair and warrants replacement.
If the turntable bearing has failed โ indicated by a loud rumbling throughout operation rather than specific impact sounds โ that's an internal motor wear failure that warrants replacement.
If the slow drain persists after cleaning the drain arm and p-trap, a camera scope of the kitchen drain line is the next step to check for blockage further downstream.
Replacement includes: safely disconnecting electrical at the junction box under the sink, removing the old unit and mounting assembly, installing the new unit with correct wiring and plumbing connections, testing for full jam-free operation, and verifying zero leaks at all connections before leaving.
No guesswork โ we diagnose before we quote, and quote before we start.
If you know the disposal is over 10 years old, tell us โ that changes how we approach the repair-vs-replace conversation upfront.
The tech identifies the failure type in minutes: jam test at the motor socket, reset button check, power confirmation at the wire connections, leak source tracing. We know what each symptom means and we go straight to confirming it.
You decide. We don't upsell replacement when repair is the right answer, and we don't push a cheap repair that won't hold on a unit that's genuinely at end of life.
After repair or replacement, we run the disposal through a full test: several cycles with water running, check under the sink for any drip at all connection points, and confirm the drain arm clears at a normal rate.

The disposal under our kitchen sink was 12 years old and started leaking from the bottom โ which the tech explained is always an internal seal failure, not a repairable condition. He had a replacement 3/4 HP InSinkErator on his truck, installed it in about 45 minutes, and the kitchen is back to normal. Old unit got pulled, new unit tested clean, no leaks at any connection.
After we added a dishwasher, it started backing up every cycle. Masters Plumbing Service found the problem immediately โ the previous installer had forgotten to knock out the dishwasher drain plug inside the disposal inlet. The plug was blocking the drain port. Two-minute fix. The tech also tightened the dishwasher drain hose clamp, which was loose. Never had another backup.
Old disposal stopped working completely โ no hum, nothing. I assumed the motor failed. The tech checked the wiring first โ found a loose wire nut at the junction box under the sink that had vibrated loose over the years. Reconnected the wire, reset the overload button, disposal came right on. Would have been embarrassing if I'd bought a replacement unit. Masters Plumbing Service's thoroughness saved me a few hundred dollars.

Masters Plumbing Service dispatches garbage disposal repair and replacement technicians throughout Upper Falls and the broader Upper Falls, MD service area. Most calls are same-day โ call to check today's availability.

Our disposal techs in Upper Falls, MD carry the tools and replacement units to resolve any disposal problem same visit. Flat-rate pricing, honest repair-vs-replace guidance, and no unnecessary upselling.
๐ Call +1-855-718-1500 Now